Pages: 220
File size: 5.34MB
License: Free PDF
Added: Vubei
Downloads: 70.959

Field Windings Continuity Test: Remove the key Item 1 [Figure ] from the axle. Remove the front auxiliary mount mounting bolts Item 1 [Figure ]. This allows the grease to escape when driving the pivot pins in to the Bob-Tach frame.

Post navigation

Figure P Connect a hoist Item 1 [Figure ] to the control valve. Lift and block the loader. Always use pcf O-rings Item 1 [Figure ]. Pre-load tension in the torsion bushings must be The bolt must be loose enough to allow the torsion removed before adjusting the steering linkage. Once removed, they need to be replaced with new.

Remove the control knob Item 2jam nut Item 1 and rubber washer Item 3 [Figure ]. Figure N Install the spool seal Item 1 [Figure ] on the linkage end of the valve. Inspect the down,oad section Item 1 [Figure ]. The box blade without laser is designed for rough grading and land scap ing.

Install the dipstick and the fill plug. Disconnect the electrical connector Item 3 [Figure ] from the traction lock solenoid. Maximum digging depths range from 6 to 11 feet. Tighten to ft. Use only new O-rings and apply oil to all O-rings and back-up rings before installation. The shaft seal flush surface Item 2 [Figure ] must be facing out away from the pump.

Arrow Indicator Plate Use a slide hammer, remove the stabilizer pivot pin Item 2 [Figure ] both sides.

Function 1 [Figure ]. Pfd The Delivery Report must be filled out by the dealer and signed by the owner or operator when the Bobcat loader is delivered. Put cloth around the tool to protect yourself from flying debris. Item 1 [Figure ] from the filter housing. Be careful, do not break the tap.

Run the engine until it is at operating temperature. When installing the pintle arm Item 1 onto the pintle base Item 2 align the rear of pintle arm engine side Item 3 into the spring Item 4 [Figure ]. Remove the gas cylinder s Item 2 [Figure ] and [Figure ] from the operator cab.

Lower the operator cab. Stabilizes the load and prevents bale rotation when handling round, uneven or square bales.

DOWNLOAD Bobcat (Bob Cat) Service, Owner’s, Parts Manual & Attachments

Remove the rollers Item 2 and the spacer Item 3 from the bolt Pvf 4 [Figure ]. Position wear plate Item 1 [Figure ] inlets and traps as shown with bronze side toward gears.

Remove the bolts Item 1 [Figure ] from the magnetic switch. Tighten the mounting bolt to ft. Item 1 [Figure ] is parallel to the driveshaft centerline. Downloda N Tighten the four bolts Item 1 [Figure ] to ft. Align the shoulder of the roller bearing Item 2 [Figure ] and [Figure ] with the beveled edge on the valve plate Item 2 [Figure ] and [Figure ]. Slide the disc Item 2 [Figure ] off the sprocket Item 1 [Figure ] and remove the disc through the front chaincase cover.

Figure P Remove the pistons Item 1 [Figure ] from the rotating block. Pilot pressure short to ground 5 volt sensor supply 1 out of range high Left swash plate sensor reversed Bobcat controller in boot code Right swash plate sensor reversed Left hand panel system RX error N Use a drift pin and hammer to remove the actuator pin Item 1 [Figure ] from the actuator and the lift or tilt spool. Re-install the plug in the drift bolt access hole after adjustment.

BOBCAT S SERVICE MANUAL Pdf Download.

Figure P If the harness has been cut: The low pressure relief valve is made up of the poppet Item 1the pdt Item 2 and the plug assembly Item 3 [Figure ]. Figure P Disconnect and remove the drain tubeline Item 1 [Figure ] from the rear auxiliary valve.

The bolt Item 2 [Figure ] must be loose enough to allow the torsion bushing to turn freely between the pintle arm and the linkage bar. P excessive wear or damage is visible, the pump must be replaced. Push the rear window out of the rear of the operator cab. N Remove the snap ring Item 1 [Figure ] from the driveshaft and remove the bearing.

Remove the bolt and nut Item 1 [Figure ] to Installation: With the seat removed, the cab will raise. Install the long threaded mannual Item 2 [Figure ] into the axle tube and through the installation tool Item 1 [Figure ].

This orifice is not removable from the valve casting.